Tag Archives: electrical

A sprinkler saga, episode 2

Mikel from Green Tree Professional returned 18 November to Emerald Hill to continue identifying problems with and repairing the sprinkler system.

With the system operable after the first repairs were made 11 November, Mikel focused in the front yard on repairing the main supply line to the sprinklers that was cut by the plumbers when they installed a new water line between the house and the city water supply at the curb.

As he dug, Mikel discovered that the main supply line for the sprinklers was cut -- pipe in left circle. The plumbers also cut two  lateral lines. Mikel has already repaired one of the laterals in this photo. The second cut is the PVC pipe in the right circle.
As he dug, Mikel discovered that the main supply line for the sprinklers was cut — pipe in left circle. The plumbers also cut two lateral lines. Mikel has already repaired one of the laterals in this photo. The second cut is the PVC pipe in the right circle.
While working on the pipes, Mikel discovered that the plumbers buried a control valve. He excavated to reveal the valve.
While working on the pipes, Mikel discovered that the plumbers buried a control valve. He excavated to reveal the valve. The plumbers also severed the control wire that runs between this valve and the next valve in line. Mikel could not locate the cut in the wires, so he opted to run new wires across the lawn to the connect the two valves.

After repairing the cuts, Mikel began testing the front sprinkler zones. He quickly discovered a lateral line that was cut when the front walk was formed — water burbled up from under one of the concrete steps.

The good news was … At least two front zones operated, even if they needed additional repairs.

It was time for Mikel to depart to his next scheduled appointment.

A sprinkler saga, episode 1

When Ranserve excavated the foundation for the new garage bay, the concrete crew cut and buried the end of the 12-strand cable that runs between the control unit location in the garage, out to the valves that control the sprinklers in the back yard, along the PVC pipes that were buried in the ground when a previous owner installed the sprinkler system, and out to the valves and sprinkler heads in the front yard.

Ron Dahlke did try to protect the cable, but bobcats, picks, shovels and form boards are brutal.

Ron, Odell, Kevin and Matt dug exploratory holes in the back yard after the garage was built — and they did find the cable.

But it had been severed — and a section about 20 feet long was missing.

Odell asked Steven to have a sprinkler company do the repair.

Steven collected four estimates. Two companies advised it would be easier and faster to install an entirely new system at a cost of somewhere beyond $4,000 to $5,000. Two companies recommended repairs at $95 an hour, plus parts, with about three hours required to diagnose whether the system could be repaired.

Steven selected Mikel and Darynn Eggert, the two brothers who run Green Tree Professional. Yes, Steven gravitates toward working with family businesses and brothers — see the fence postings as further evidence.

In episode 1 of the sprinkler saga, dated 11 Nov. 2016, Darynn and Mikel excavated the cut end of the control cable buried in the ground about feet away from the back of the new garage, patched it to new wire, and attempted to pull that wire into the garage through conduit that was fixed into place when the concrete slab of the new garage floor was poured.

First discovery — it is impossible to force heavy-duty 12-strand irrigation wire through a tight 90-degree elbow when you don’t have a heavy-duty pull cord.

1-dsc_3842
The concrete team installed electrical conduit when they formed and poured the new slab for the garage. The sprinkler control wire was supposed to travel through the conduit. But, the wire can’t be pulled through the tight elbow identified in the lower circle in photo, at the concrete foundation. Steven approved drilling through the siding — the second, higher circle in the red-painted siding. Note the missing chunk of concrete walk that was cut out when the garage slab was excavated — this has to be replaced. Darynn and Mikel ran a temporary control wire above ground, with which they were able to begin testing the sprinkler system.

After much discussion, Steven permitted Darynn and Mikel to drill a hole through the exterior siding of the garage above ground level, with a plan to shield the cable in new conduit that would be mounted to the exterior of the siding outside the garage, turned down to the ground in a WIDE 90-degree elbow, then buried and run out across the back yard to connect with the old existing cable.

Except … Ranserve still has to replace a chunk of concrete walk that was cut out when the garage foundation was formed and poured. The new wire out the back of the garage traverses this missing concrete, so permanent installation is not possible until the concrete work is done.

The temporary control wire travels about 20 feet across the back yard to where the original exiting wire was severed.
The temporary control wire travels about 20 feet across the back yard to where the original exiting wire was severed.
Darynn and Mikel made waterproof connections between the new and old control wires. The trench at right is where Mikel discovered the open end of a sprinkler line that was severed during construction of the garage. He cut off the knife edge of the PVC and capped it off.
Darynn and Mikel made waterproof connections between the new and old control wires. The trench at right is where Mikel discovered the open end of a sprinkler line that was severed during construction of the garage. He cut off the knife edge of the PVC and capped it off.

So, Mikel and Darynn ran the wire into the garage, temporarily loose and above ground, connected it to the sprinkler controller in the back yard, turned on water to the sprinkler system, powered up the controller — and began experimenting to discover leaks.

Second discovery — the system still worked. In some places.

Third discovery — in the front yard, the plumbers severed  the main supply line to the sprinkler system when they trenched the front yard to install the new water supply line to the house as required by the city. Did the plumbers repair the sprinkler line as requested by Steven? Apparently, obviously, not.

 

Steve the electrician to the rescue

Steve the electrician is back in the house, this time to solve a mystery — why does the breaker for the oven not turn off power to the oven in the kitchen when the breaker is flipped to the off position?

Steve flips breakers while Steven in the kitchen watches to see which one actually turns off the oven.

We find it quickly. The “dryer” breaker is mislabeled; it is the breaker that controls the oven.

And, oh by the way, the breaker labeled for the furnace is actually the breaker that switches off the induction cooktop.

IMG_20160630_211628Problem solved. Quality control.

With that, the Bosch oven is now, finally, powered off. Steven flips the breaker to the on position about 30 minutes later. The oven appears to have re-set, with the keypad now responding to commands and entries. Jacquela will have to test this to her satisfaction. Steven does not cancel the service call scheduled for 5 July.