The quartz countertops have been moved out of storage and placed atop the vanities in bath 2 and the master bath — gray in the master, above, and white in Jadin’s bath, aka bath 2, below.
Yes. It is.
We’ve been waiting for this.
Jacquela wanted a red glass backsplash behind the cooktop. We researched and priced a sheet of red back-painted glass, four feet wide by five feet tall. The estimates came in at more than $2,000 and the installer refused to warranty the glass against breakage, because we are mounting a pot-filler spigot above the cooktop, and the exhaust fan above that — and every hole in the sheet of glass compromises its integrity.
Plan B is red glass tiles, four inches tall by 12 inches wide.
Julian and Ernesto today installed the tile.
Don’t tell Jacquela and Ron. Steven went for a walk on the roof to see the new cricket atop the existing garage, and the new roof of the new garage structure.
The roofers “dried in” the roofs today. That highly technical term means the roof is basically waterproof — which is good, because the forecast calls for rain.
Above, tar paper is tacked down on the roof over the new garage structure.
Steven today asked the plumbers to hold on installation of the Toto toilets in bath 2 and the master bath.
We have questions about the Toto bidet installation and materials.
- The water line between the bowl and the bidet is plastic. Thin plastic, albeit reinforced with some kind of cross-hatched material. Each end is a crimped fitting. Steven is surprised. He would have expected stainless steel, reinforced. Does Toto offer this alternative? If so, how did we miss speccing it?
- Installing the plastic water line is proving to be “different and difficult,” to paraphrase the plumbers. They normally install the tank to the bowl, then set the toilet, then install the seat. As the plumbers explain what is happening, here, instead, they are forced to install the tank to the bowl, then install the seat, then set the toilet – because there is no way to get to the water line fitting at the back of the toilet unless you are working with a toilet that is not mounted to the floor. As a result, envision the day when the plastic water line blows or leaks, and it will, just because. Steven will be forced to call a plumber who unmounts the entire toilet from the floor just to get to the fitting, before that plumber can begin to work on the leak. This is not the brilliant design expected of Toto – forcing the homeowner to remove a toilet just to repair a water line if and when that water line must be repaired – and supplying a plastic water line instead of stainless steel, boosting the chance that there will be a problem with that plastic line. And, crimped fittings instead of threaded?
- The plumbers tell Steven there are other Toto toilet designs that we could have selected – not the skirted models – that make it easier to install the bidet seat while also diminishing the potential for water-line failure. Did we screw up selecting these Toto models? Do we have the option to swap out the toilets we selected for comparable Toto models that the plumbers consider the better choice?
- The plumbers also ask if there is a T-fitting that allows them to connect the toilet and the bidet to the water line coming out of the wall? Right now, the water line to the bidet routes from the tank atop the bowl, not to the water line coming out of the wall. This would give them more flexibility in the installation.
Ron will now explore these questions and options with Jonell at Ferguson.
Not including earlier discussions, Ron and Steven, with help from carpenters Shane and Peter, debated what size door strike we need at which door — and where to install the oversized pull and smart deadbolt system on the front door.
Why? Working with architect Brett, Steven and Jacquela opted months ago for oversized trim around the doors. It’s not wide, but it is deep — standing more than one inch proud of the drywall. That aesthetic decision now cascades into a rude realization — standard-sized strike plates are not wide enough to protect the trim when the latch bolt slides across the painted trim. The bolt leaves a trail across the paint.
With Shane’s help, we sized the kitchen side door for strike plate 2.25 inches tall by 3 inches wide. Standard width is more like one inch. All the other interior and exterior doors — with the exception of the front door — need strike plates 2.25 inches tall by 2.5 inches wide.
Steven shopped and ordered these online from Amazon.
The front door is a different conundrum. According to Shane, the handle on a front door is normally mounted 36 inches up from the bottom of the door.
If we mount the oversized pull at that height on the door, the pull will appear way too low, located properly only for very short people.
We debated different heights for a while, shifting the pull up and down and calculating where to put the smart deadbolt above it. We decided that the top of the pull should be 54 inches up from the bottom of the door.
Ron wrote this decision down.
About three hours later, Ron called Steven to note that we forgot to compute into the 54 inches the fact that there is a step up from the porch to the front door — about seven inches.
That was yesterday.
Today, we used blue painter’s tape to mock up the potential positions on the OSB sheets that currently cover the front door. One at 36 inches, one at 54 inches.
54 inches is where your hand meets the pull comfortably. The smart deadbolt mounts a short reach higher, at just about eye height for adults. Jadin is already nearly as tall as Mom and Dad — so that height is going to work just fine.
Now it’s up to Shane and Peter to drill holes in the door to mount the hardware.
But we take away these instructions:
- Every small decision cascades into many more decisions that are complicated, time consuming, expensive, surprises to even experienced carpenters and builders, surprises that Steven could not anticipate or imagine.
- Every cascading decision comes with multiple complexities. Take a deep breath. Dive in. Talk it through. As many times as necessary. Use tape for mockups. Get as many hands and brains involved as necessary. Solve the puzzle. And the next puzzle. And the puzzles just don’t stop arriving.